CalcGallery

Stone Veneer Calculator

Work out flat stone and corner pieces for a veneer wall, allowing for the wall the corners already cover, plus scratch coat and mortar bags.

Built by AbhiLast reviewed November 6, 2026

Units
Walls to cover

Your measurements

Add one row per wall or section.

Doors, windows and anything else the stone stops at, added together.

Add the height of every outside corner. Leave at 0 if there are none.

The average length of the long leg of a corner piece, from the product sheet. It is what lets the page deduct flat stone.

Optional. From the mix you buy, at the thickness you will apply.

Optional. From the product sheet. Jointed stone uses more than a dry-stacked look.

Result

Enter walls to cover to see the result.

Your entries are kept on this device only.

Results are estimates for planning only. Actual needs vary with site conditions, products and workmanship. Always confirm quantities with your supplier and follow local building codes and manufacturer instructions. Read the full disclaimer

How to use the Stone Veneer Calculator

  1. Add each wall as a row and enter the openings to subtract.
  2. Add up the height of every outside corner, and enter the return width of your corner pieces.
  3. Enter the bag coverage for your scratch coat and mortar if you want bag counts.
  4. Order the flat area and the corner length separately.

How the order is worked out

Net wall    = walls − openingsCovered     = corner length × return widthFlat stone  = (net wall − covered) × (1 + allowance)Bags        = net wall ÷ coverage per bag, rounded up

Competing tools work stone out by cubic volume, which suits a solid stone wall. Veneer is thin and sold by the face, so here the answer is a surface area and a corner length, the two lines on a supplier’s order.

Buy one batch

Colour varies between production runs and between quarry lots, so order the whole job at once. Lay out stones from several boxes on the ground before you start, and blend them as you go.

Scope and safety

Veneer adds weight and sits on a drainage layer, so the wall behind it matters. This page does not design that assembly, and local codes vary. Follow the product installation guide for lath, weather barrier, clearances to grade and flashing.

With your numbers

  1. Net wall = walls − openings = 140 ft²
  2. Corners cover 16 ft × the return width = 8 ft²
  3. Flat stone = (net − corners) × (1 + 5%) = 138.6 ft²

Quick reference

Natural shapes are cut to fit around corners and openings, so a little extra saves a second order that may not match.

Common jobs, worked out with the options this calculator starts on for United States.
JobFlat stone to order
20 × 8 ft wall with 2 corners138.6 ft²
16 × 3 ft wainscot47.25 ft²
Fireplace, 6 × 8 ft29.4 ft²
40 × 9 ft front, 2 openings316.05 ft²
No corners, 10 × 8 ft84 ft²
6 × 2.4 m wall12.26 m²
Fireplace, 2 × 2.4 m3.23 m²

Where the numbers come from

The fixed figures this calculator relies on, and the published source each one was checked against. How the calculators are built and checked

1 source
  1. Brick Industry Association, Technical Note 10 "Dimensioning and Estimating Brick Masonry" (Feb 2009), Brick breakage and waste: add at least 5%, https://gobrick.com/media/file/10-dimensioning-and-estimating-brick-masonry.pdf

    Used for

    • Brick or block allowance: 5% extra

Common questions about the Stone Veneer Calculator

Do I subtract corners from the flat stone order?
Yes. The long leg of each corner piece sits on the wall, so that part needs no flat stone. A 16 ft corner run with 6 in returns already covers 8 square feet.
How do I measure outside corners?
Add the height of each outside corner. Two corners on an 8 ft wall make 16 linear feet. Inside corners take flat stone cut to fit, so leave them out.
What is a scratch coat?
A base coat of mortar, scored while wet so the stone mortar can key into it. Many veneers go over lath with a scratch coat, but your product sheet decides what your wall needs.
Why does this ask for my mortar coverage?
Coverage changes with the stone shape, joint width and bag size. Figures from a sheet for your exact product are better than one general number.

Report a problem with this calculator