CalcGallery

Shed Materials Calculator

Estimate the floor, wall and roof sheets plus the studs, joists and rafters for a rectangular gable shed in one go.

Built by AbhiLast reviewed November 6, 2026

Units
Width, across the gable

Your measurements

Centre to centre, used for studs, joists and rafters. Follow your plan.

A 4 × 8 ft sheet is 32 ft², and a 1.2 × 2.4 m sheet is 2.88 m².

Result

Buy 18 sheetsEstimate

Floor, walls and roof, each rounded up

No waste is added by default. Use Custom for cuts around doors, windows and gables.

Floor sheets
3Estimate
Wall sheets, gables included
11Estimate
Roof sheets
4Estimate
Wall studs
34Estimate
Floor joists
10Estimate
Rafters
20Estimate
Rafter length
4.47 ft (53.67 in, 1.36 m)
Report a problem with this calculator
Your entries are kept on this device only.

Results are estimates for planning only. Actual needs vary with site conditions, products and workmanship. Always confirm quantities with your supplier and follow local building codes and manufacturer instructions. Read the full disclaimer

How to use the Shed Materials Calculator

  1. Enter the shed length, its width across the gable, and the wall height.
  2. Enter the roof pitch and any overhang.
  3. Set the framing spacing and the size of your sheets.
  4. Take the sheet and framing counts to your supplier as a first estimate.

How the estimate adds up

Floor sheets = length × width ÷ sheet areaWall sheets  = (2 × (length + width) × height + gables) ÷ sheet areaRoof sheets  = (width + 2 × overhang) × slope factor × (length + 2 × overhang) ÷ sheet area

Each surface rounds up on its own, because a part sheet left from the floor is rarely any use on the roof. Studs, joists and rafters come from the spacing, one more member than gaps on each run.

Using it with the other pages

This page gathers a whole shed into one list. For the detail, use the framing page for plates and door openings, the plywood page for layouts, and the roofing pages for shingles and underlayment on the area you end up with.

Scope

A rectangular gable shed with one pitch. Windows and doors are not deducted, so a little spare sheet is normal. Foundations, anchoring and structural sizing are outside this page.

With your numbers

  1. Floor = 3 sheets, walls and gables = 11, roof along the slope = 4
  2. Framing = 34 studs, 10 joists, 20 rafters
  3. Sheets in all = 18 sheets

Quick reference

No waste is added by default. Use Custom for cuts around doors, windows and gables.

Common jobs, worked out with the options this calculator starts on for United States.
JobSheets in all
8 × 12 ft, 6 in 1218
10 × 12 ft, 12 in overhang22
10 × 16 ft, 4 in 1227
6 × 8 ft, 24 in spacing12
12 × 20 ft37
3.6 × 2.4 m18
4.8 × 3 m27

Common questions about the Shed Materials Calculator

How many sheets of plywood for an 8 by 12 shed?
With 8 ft walls and a 6 in 12 roof, about 3 for the floor, 11 for the walls and gables, and 4 for the roof: 18 in all, before any waste.
Are plates and door framing included?
No. Top and bottom plates, headers, door and window studs and blocking change with your plan, so add those from the framing page or your drawing.
Does this tell me what size lumber to use?
No. It counts members but does not size them. Joist, rafter and foundation choices depend on span, load and local code.
Do I need a permit for a shed?
It depends on size, height and location. Local rules vary, so check with your building department first.

Report a problem with this calculator