CalcGallery

Metal Weight Calculator

Estimate the weight of steel or aluminium plate, round bar, box tube and angle from its dimensions.

Built by AbhiLast reviewed November 6, 2026

Units
Thickness

Your measurements

Result

Total weight: 102.1 lbEstimate

This is a weight, not a purchase, so nothing is added.

Weight of one piece
102.1 lb (46.31 kg)Estimate
Weight per metre
15.194Estimate
Kilograms per metre
Cross-section
0.0208 ft² (0.0019 m²)
Report a problem with this calculator
Your entries are kept on this device only.

Results are estimates for planning only. Actual needs vary with site conditions, products and workmanship. Always confirm quantities with your supplier and follow local building codes and manufacturer instructions. Read the full disclaimer

How to use the Metal Weight Calculator

  1. Pick steel or aluminium, then the shape of the piece.
  2. Enter its dimensions and length.
  3. Enter how many pieces you have.
  4. Use the weight per metre to compare sections or plan lifting.

How the weight is worked out

Plate   area = width × thicknessBar     area = π ÷ 4 × diameter²Tube    area = a × b − (a − 2t) × (b − 2t)Angle   area = t × (a + b − t)Weight  = area × length × density × quantity

Finding the area of the cross-section first means the same formula works for every shape, and it is why the page can show a weight per metre as well.

Why the alloy barely matters here

Different steels and aluminium alloys vary by only a small percentage in density, so one figure for each metal is enough for handling and shipping estimates. Stainless and brass are heavier than these and are not covered.

Handling

Weight affects how you lift, move and support a piece. Check the safe load of hoists, racks and vehicles rather than relying on this estimate alone.

With your numbers

  1. Volume = cross-section × 10 ft long
  2. Each = that volume × density = 102.1 lb
  3. Total = 1 × each = 102.1 lb

Quick reference

This is a weight, not a purchase, so nothing is added.

Common jobs, worked out with the options this calculator starts on for United States.
JobTotal weight
12 in × 1/4 in steel flat, 10 ft102.1 lb
1 in steel round bar, 10 ft26.73 lb
2 × 2 × 1/8 in steel tube, 20 ft63.81 lb
2 × 2 × 1/4 in steel angle, 20 ft63.81 lb
1/8 in aluminium flat, 12 in, 8 ft14.05 lb
1 m × 10 mm steel plate, 1 m78.5 kg
20 mm steel bar, 6 m14.8 kg
50 × 50 × 3 mm aluminium tube, 6 m9.14 kg

Where the numbers come from

The fixed figures this calculator relies on, and the published source each one was checked against. How the calculators are built and checked

2 sources
  1. Iowa DOT, Instructional Memorandum 569, "Computing Structural Steel Weight (Mass)": steel 490 lb/ft³ (7850 kg/m³), https://ia.iowadot.gov/erl/current/IM/content/569.htm

    Used for

    • Density of structural steel, 490 lb/ft³.
  2. Handbook figure for 6061-T6 of 0.098 lb/in³, as listed in https://engineeringmechanicsoer.github.io/StrengthBook/Appendix%20C.html. The Aluminum Association primary table was not read; the founder should check it.

    Used for

    • Density of common wrought aluminium such as 6061, 0.098 lb/in³.

Common questions about the Metal Weight Calculator

How much does a steel plate weigh?
Multiply its volume by the density of steel, 490 pounds per cubic foot. A plate 1 m square and 10 mm thick comes to 78.5 kg.
Is aluminium really a third the weight of steel?
Close to it. Aluminium at 2,700 kg per cubic metre is about 34% of steel at 7,850 for the same dimensions.
Why does my supplier's weight differ?
Rolled tube and angle have rounded corners, and sizes have tolerances. Treat this as an estimate and use the mill or supplier figure when weight is critical.
Can this tell me how strong a section is?
No. It gives weight only. Strength, span and connections are a structural question for a qualified engineer.

Report a problem with this calculator